ATTENTION:<\/strong><\/p>\n\n\n\n BEFORE YOU READ THE ABSTRACT OR CHAPTER ONE OF THE PROJECT TOPIC BELOW, PLEASE READ THE INFORMATION BELOW.THANK YOU!<\/strong><\/p>\n\n\n\n INFORMATION:<\/strong><\/p>\n\n\n\n YOU CAN GET THE COMPLETE PROJECT OF THE TOPIC BELOW. THE FULL PROJECT COSTS N5,000 ONLY. THE FULL INFORMATION ON HOW TO PAY AND GET THE COMPLETE PROJECT IS AT THE BOTTOM OF THIS PAGE. OR YOU CAN CALL: 08068231953, 08168759420<\/strong><\/p>\n\n\n\n WHATSAPP US ON 08137701720<\/strong><\/p>\n\n\n\n KINETIC STUDIES OF THE ADSORPTION OF HEAVY METALS (CHROMIUM) FROM INDUSTRIAL WASTE WATER USING PALM KERNEL SHELL AND CHARCOAL<\/strong><\/p>\n\n\n\n CHAPTER ONE<\/p>\n\n\n\n INTRODUCTION<\/p>\n\n\n\n Background to Study<\/p>\n\n\n\n At least 20 metals are classified as toxic and half of these are emitted into the environment in quantities that pose risks to human health (Kortenkamp et. al. 1996). Chromium has both beneficial and detrimental properties. Two stable oxidation states of chromium persist in the environment, Cr (III) and Cr (VI), which have contrasting toxicities, mobilities and bio availabilities. Whereas Cr (III) is essential in human nutrition (especially in glucose metabolism), most of the hexavalent compounds are toxic, several can even cause lung cancer. While Cr (III) is relatively innocuous and immobile, Cr (VI) moves readily through soils and aquatic environments and is a strong oxidizing agent capable of being absorbed through the skin (Park and Jung, 2001). Chromium and its compounds are widely used in electroplating, leather tanning, cement, dyeing, metal processing, wood preservatives, paint and pigments, textile, steel fabrication and canning industries These industries produce large quantities of toxic wastewater effluents (Raji and Anirudhan, 1997). The maximum concentration limit for Cr (VI) for discharge into inland surface waters is 0.1 mg\/l and in potable water is 0.05 mg\/l (EPA, 1990).<\/p>\n\n\n\n A wide range of physical and chemical processes is available for the removal of Cr (VI) from wastewater, such as electro-chemical precipitation, ultra filtration, ion exchange and reverse osmosis (Rengaraj et al. 2001; Yurlova et al. 2002; Benito and Ruiz, 2002). A major drawback with precipitation is sludge production. Ion exchange is considered a better alternative technique for such a purpose. However, it is not economically appealing because of high operational cost. Adsorption using commercial activated carbon (CAC) can remove heavy metals from wastewater, such as Cd (Ramos et al. 1997); Ni (Shim et al. 2001); Cr (Ouki et al. 1997); Cu (Monser and Adhoum, 2002). However, CAC remains an expensive material for heavy metal removal.<\/p>\n\n\n\n Natural biopolymers are industrially attractive because of their capability of lowering transition metal-ion concentration to parts per billion concentrations. Natural materials that are available in large quantities or certain waste from agricultural operations may have potential to be used as low cost adsorbents, as they represent unused resources, widely available and are environmentally friendly (Deans and Dixon, 1992). In Malaysia, oil palm is the most important commercial crop. The explosive expansion of oil palm plantation has generated enormous amounts of vegetable waste. It was reported that Malaysia currently produces about 30 million tonnes annually of oil palm biomass, including trunks, fronds, fruit waste and empty fruit brunches. Of these, about two million tonnes of fruit shell (or endocarp) is generated annually (Chan, 1999). Preliminary studies have shown that it is feasible to prepare chars with sufficient densities and high porosity from oil palm fruit waste (Guo and Lua, 1998). The exchange\/sorption properties of palm oil shell are due to the presence of some functional groups, such as carboxylic, hydroxyl, and lactone, which have a high affinity for metal ions (Tan et al. 1993). In recent years, development of surface modified activated carbon has generated a diversity of activated carbon with far superior adsorption capacity. The use of palm oil shell with surface modification to improve its metal removal performance would add its economic value, help reduce the cost of waste disposal, and most importantly, provide a potentially inexpensive alternative to existing commercial activated carbon.<\/p>\n\n\n\n Statement of Problem<\/p>\n\n\n\n Chitosan chelates five to six times greater amounts of metals than chitin. This is attributed to the free amino groups exposed in chitosan because of deacetylation of chitin (Yang and Zall, 1984). The biosorbent material, chitosan, is slightly soluble at low pHs and poses problems for developing commercial applications. It is also soft and has a tendency to agglomerate or form a gel in aqueous solutions. In addition, the active binding sites of chitosan are not readily available for sorption. Transport of the metal contaminants to the binding sites plays a very important role in process design. Therefore, it is necessary to provide physical support and increase the accessibility of the metal binding sites for process applications.<\/p>\n\n\n\n Among the many other low cost absorbents identified (Olin et al. 1996; Bailey et al. 1999, Bailey et al. 1997) chitosan has the highest sorption capacity for several metal ions (Deshpande, 1986). Chitin (2-acetamido-2-deoxy-\u03b2-D-glucose-(N-acetylglucan) is the main structural component of molluscs, insects, crustaceans, fungi, algae and marine invertebrates like crabs and shrimps (Deshpande, 1986; Chen and Chang, 1994; Ilyina et al. 1995). Worldwide, the solid waste from processing of shellfish, crabs, shrimps and krill constitutes large amount of chitinaceous waste.<\/p>\n\n\n\n Chitosan (2-acetamido-2-deoxy-\u03b2-D-glucose-(N-acetylglucosamine) is a partially deacetylated polymer of chitin and is usually prepared from chitin by deacetylation with a strong alkaline solution.<\/p>\n\n\n\n In the present investigation an attempt was made to overcome these mass transfer limitations by synthesizing a biosorbent by coating chitosan on the surface of palm oil shell charcoal and evaluating its equilibrium adsorption properties. The combination of the useful properties of oil palm shell char and that of natural chitosan, could introduce a composite matrix with many application and superior adsorption capabilities. Using synthetic wastewater, the Cr removal by oil palm shell charcoal coated with chitosan and acid treated oil palm shell charcoal adsorbents were statically compared.<\/p>\n\n\n\n Research Objectives<\/p>\n\n\n\n The broad objective of this research project is to carry out kinetic studies of the adsorption of heavy metals (chromium) from industrial waste water using palm kernel shell and charcoal.<\/p>\n\n\n\n The specific objectives however are:<\/p>\n\n\n\n To carry out a synthesis of biosorbent by coating chitosan on the surface of palm oil shell charcoal<\/p>\n\n\n\n To evaluate the equilibrium adsorption<\/p>\n\n\n\n To statically compare the Cr removal by oil palm shell charcoal coated with chitosan and acid treated oil palm shell charcoal adsorbents using synthetic wastewater.<\/p>\n\n\n\n HOW TO RECEIVE PROJECT MATERIAL(S)<\/strong><\/p>\n\n\n\n After paying the appropriate amount (#5,000) into our bank Account below, send the following information to<\/strong><\/p>\n\n\n\n 08068231953 or 08168759420<\/strong><\/p>\n\n\n\n (1) Your project topics<\/p>\n\n\n\n (2) Email Address<\/p>\n\n\n\n (3) Payment Name<\/p>\n\n\n\n (4) Teller Number<\/p>\n\n\n\n We will send your material(s) after we receive bank alert<\/p>\n\n\n\n BANK ACCOUNTS<\/strong><\/p>\n\n\n\n Account Name: AMUTAH DANIEL CHUKWUDI<\/p>\n\n\n\n Account Number: 0046579864<\/p>\n\n\n\n Bank: GTBank.<\/p>\n\n\n\n OR<\/p>\n\n\n\n Account Name: AMUTAH DANIEL CHUKWUDI<\/p>\n\n\n\n Account Number: 3139283609<\/p>\n\n\n\n Bank: FIRST BANK<\/p>\n\n\n\n FOR MORE INFORMATION, CALL:<\/strong><\/p>\n\n\n\n 08068231953 or 08168759420<\/strong><\/p>\n\n\n\n AFFILIATE LINKS:<\/a><\/p>\n\n\n\n easyprojectmaterials.com<\/a><\/p>\n\n\n\n